DIY 3D Paper Holly Gift Topper

DIY 3D Paper Holly Gift Topper | CorinnaWraps.wordpress.com

Deck the halls — er, gifts with boughs of holly!

This DIY paper gift topper takes advantage of the natural curl of rolled gift wrap to create 3D holly leaves. Add a handful of 3D berries and you get an impressive decoration for that extra-special gift.

The instructions below are for the embellishment as shown, but experiment with the arrangement and size of the berries and leaves: A large arrangement as shown here works great on a shirt box–sized gift, while a miniature cluster of three berries and two leaves would look nice on a small jewelry box. Or try a garland of many leaves and berry clusters cascading across an oversized gift.

Scotch

SPONSORED CONTENT This post is brought to you by 3M™ Scotch® Brand. Visit the Scotch® Brand Style Blog for more information and great DIY inspiration!

SKILL LEVEL: Advanced

TIME NEEDED: Approximately 30 to 45 minutes

DIY 3D Paper Holly Gift Topper | CorinnaWraps.wordpress.com

SCOTCH® BRAND SUPPLIES 

OTHER SUPPLIES/TOOLS

  • Gira Pearl paper in Coral from The Paper Place
  • Green metallic foil paper (on a roll) from DeSerres
  • Candy Flake gift wrap in white from The Paper Place
  • Teal satin ribbon
  • 1 1/4” circle punch
  • Pencil
DIY 3D Paper Holly Gift Topper | CorinnaWraps.wordpress.com

1. Make the holly berries. Using a circle punch, cut 21 circles from the pink paper. (This is the amount you will need to create the holly shown in this project. Make more or less depending on how many berries you need for your design; it takes three circles to make each berry.)

Fold each circle in half. Apply Scotch® Scrapbooker’s Glue to the back of half of a circle, then align with the back half of a second circle and stick together. Do the same with a third circle to complete one berry, then repeat these steps again until you have seven berries.

DIY 3D Paper Holly Gift Topper | CorinnaWraps.wordpress.com

2. Make the holly leaves. Cut 12 squares of green paper, approximately five inches square. (Just like with the berries, this is for the design shown here; you may want more or fewer leaves for your gift).

Fold each paper square in half so the right-side is facing in and the curl of the paper runs lengthwise. Draw half a holly leaf onto the back of each — the shape is basically a wave with two arched peaks. (If you find drawing freehand difficult, draw on a scrap piece of cardboard until you are happy with the shape, then cut out and use as a template.) Cut out each leaf using Scotch® Precision Ultra Edge Scissors.

3. Wrap your box. Using your Scotch® Precision Ultra Edge Scissors and Scotch® Permanent Double Sided Tape, wrap your gift in the white glitter paper. Wrap the ribbon around the middle of the gift (cutting off any excess length) and glue the ends in place at the centre of the front with Scotch® Quick-Dry Adhesive. (Don’t worry about being too tidy — the holly will hide the ribbon ends.)

DIY 3D Paper Holly Gift Topper | CorinnaWraps.wordpress.com

4. Attach the holly to your gift. Apply Scotch® Quick-Dry Adhesive to the back of a tip of a leaf and attach to the centre of the gift. Repeat with the remaining leaves, working around to create a circle of overlapping leaves until they’re all attached. Next, apply Scotch® Quick-Dry Adhesive to the backs of the berries and attach in a cluster over the centre of the leaf arrangement. You’re done! Happy holidays!

EXPERT TIP

Play with colour! Here I went with a retro-inspired shimmery palette of pink, green, peacock and glittery white, but I was torn when I was choosing: imagine it in a traditional combo of velvety red berries and deep green leaves with glossy white paper and red ribbon, or for an eye-popping take on the classic holly motif, try lime green leaves and persimmon berries, with tangerine paper and magenta ribbon.

DIY 3D Paper Holly Gift Topper | CorinnaWraps.wordpress.com